- 您现在的位置：买卖IC网 > Sheet目录335 > ISPNANO S3 KIT (Equinox Technologies)ISP PORTABLE PROGRAMMER
1.11 Programmer Specifications
The table below details the hardware specifications for the programmer. Please refer to the stated
section for further information about any specific parameter.
#
Parameter
Description / comment
Refer
to
section
1
2
Target Device
Support
Target Device
Programming
See Device Support List (separate document)
The ISPnano Series I and II programmers supports the
following programming interfaces:
Interfaces
?
?
?
?
?
?
?
Atmel Low Voltage SPI
Atmel High Voltage SPI (+12V Vpp)
Atmel AVR JTAG (chargeable update)
Atmel (formerly Temic) 8051 Boot loader ISP
NXP (Philips) 8051 - Boot Loader ISP
Generic I2C (SDA + SCL)
ARM7 JTAG Debug Interface
The ISPnano Series III programmer supports all of the above
programming interfaces plus the following additional interfaces:
?
?
Atmel XMEGA 2-wire PDI interface
Atmel ATtiny 2-wire TPI interface
3
Operating modes
The programmer supports the following operating modes:
Development Mode (PC controlled)
?
Project Upload Mode (PC controlled)
?
Standalone Mode – Single Start button mode
?
Standalone Mode – Automatic Target Connect / Disconnect
?
Sensing
Standalone Mode - Remote Controlled via ‘ASCII Text
?
Communications’ RS-232 Serial Protocol
Standalone Mode - Remote Controlled via 4-wire TTL
?
Remote Control Port
PC controlled via ISP-PRO software (chargeable upgrade)
?
PC controlled via ConsoleEDS utility (chargeable upgrade)
?
4
On-board FLASH
Memory Store
?
128 Mbits (16 MBytes) FLASH Memory for Project
Storage
5
6
Project storage in
Memory Store
Keypad entry
64 x Programming Projects
1 x <START> button
7
Status LED’s
i.
3 x Status LED’s located on the programmer:
<PASS>, <BUSY>, <FAIL>
ii.
iii.
3 x remote Status LED’s can also be connected off-
board on a Test Fixture via the ‘Remote System
Status’ port.
1 x Bi-coloured status LED
10 PC Control Software The programmer can be controlled using:
?
EQTools (as standard)
ISPnano Series Programmer - User Manual – V1.11 – 12 May 2011
th
19
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
IX2127N
IC HIGH SIDE DRIVER 8SOIC
IX2R11S3T/R
IC DRVR HALF BRIDGE 2A 16-SOIC
IX4R11S3T/R
IC DRVR HALF BRIDGE 4A 16-SOIC
IX6R11S6T/R
IC DRVR HALF BRIDGE 4A 18-SOIC
IXA531S10T/R
IC BRIDGE DRVR 3PH 500MA 48-MLP
IXA611S3T/R
IC DRIVER HALF BRDG 600MA 16-SOI
IXBD4410PI
IC LOW SIDE DRIVER 16DIP
IXD611S7T/R
IC DRVR HALF BRIDGE 600MA 14SOIC
相关代理商/技术参数
ISPNANO UPG17
功能描述:ISP NANO DEVICE LIB UPGRAGE RoHS:是 类别:编程器，开发系统 >> 知识产权 (IP) 系列:* 标准包装:1 系列:Nios®II 类型:Nios II 功能:C 到硬件编译器 许可证:初始许可证
ISPNANO-UPG10AR
功能描述:ISP NANO RUN TIME LICENSE RoHS:否 类别:编程器，开发系统 >> 知识产权 (IP) 系列:* 标准包装:1 系列:Nios®II 类型:Nios II 功能:C 到硬件编译器 许可证:初始许可证
ISPNANO-UPG18
功能描述:ISP PORTABLE PROGRAMMER USB RoHS:是 类别:编程器，开发系统 >> 软件 系列:* 标准包装:1 系列:ISE® 设计套件 类型:订阅 适用于相关产品:Xilinx FPGAs 其它名称:Q4986209T1081384
ISPNANO-UPG7
功能描述:JTAG ISP UPGRADE FOR ATMEL AVR RoHS:否 类别:编程器，开发系统 >> 知识产权 (IP) 系列:* 标准包装:1 系列:Nios®II 类型:Nios II 功能:C 到硬件编译器 许可证:初始许可证
ISPN-UPG10M
功能描述:ISP PORTABLE PROGRAMMER USB RoHS:是 类别:编程器，开发系统 >> 软件 系列:- 标准包装:1 系列:ISE® 设计套件 类型:订阅 适用于相关产品:Xilinx FPGAs 其它名称:Q4986209T1081384
ISPPAC10
制造商:LATTICE 制造商全称:Lattice Semiconductor 功能描述:In-System Programmable Analog Circuit
ISPPAC10-01PI
功能描述:SPLD - 简单可编程逻辑器件 PROGRAMMABLE ANALOG CIRCUIT RoHS:否 制造商:Texas Instruments 逻辑系列:TICPAL22V10Z 大电池数量:10 最大工作频率:66 MHz 延迟时间:25 ns 工作电源电压:4.75 V to 5.25 V 电源电流:100 uA 最大工作温度:+ 75 C 最小工作温度:0 C 安装风格:Through Hole 封装 / 箱体:DIP-24
ISPPAC10-01SI
功能描述:SPLD - 简单可编程逻辑器件 PROGRAMMABLE ANALOG CIRCUIT RoHS:否 制造商:Texas Instruments 逻辑系列:TICPAL22V10Z 大电池数量:10 最大工作频率:66 MHz 延迟时间:25 ns 工作电源电压:4.75 V to 5.25 V 电源电流:100 uA 最大工作温度:+ 75 C 最小工作温度:0 C 安装风格:Through Hole 封装 / 箱体:DIP-24